
Trying Out The OTC Hub Grappler 6575 Kit
video description
Date: 2020-08-05
Related videos
Comments and reviews: 9
Michael
Love you vids.
Q: Why do you have faith that the hub was in good order regarding run-out and deflection?
Previous owners of my car never balanced tires evidently aad the steel rims wobbeled. back. abd forth eating up the cast iron hubs.
Hubas for non-luxury passenger cars seem to be 30-60 aftermarket. Inexpensive piece of mind to ensure a good base foe the brake disc.
reply
Love you vids.
Q: Why do you have faith that the hub was in good order regarding run-out and deflection?
Previous owners of my car never balanced tires evidently aad the steel rims wobbeled. back. abd forth eating up the cast iron hubs.
Hubas for non-luxury passenger cars seem to be 30-60 aftermarket. Inexpensive piece of mind to ensure a good base foe the brake disc.
reply
Rocky
Hey Eric, Im sure that you have tried the old ball peen hammer trick. Place the hub race against the flat top part of an anvil and give it a couple of hard hits with the round part of the hammer. MAKE SURE that you are wearing a face shield and protective clothing because sharp broken pieces of the race will go flying in every direction. Its an old farmers trick.
reply
Hey Eric, Im sure that you have tried the old ball peen hammer trick. Place the hub race against the flat top part of an anvil and give it a couple of hard hits with the round part of the hammer. MAKE SURE that you are wearing a face shield and protective clothing because sharp broken pieces of the race will go flying in every direction. Its an old farmers trick.
reply
JCcanU
OTC are USA made Warren Michigan just outside Detroit in the Industrial Part of Warren I buy a lot of tools from OTC Harley Davidson or Jims Tools are 3 times the price as OTC and I can say OTC has high grade tools. 4 tool that Jims was asking 300 each I got for 100 each from OTC. I spent 400 on tools not 1200.
reply
OTC are USA made Warren Michigan just outside Detroit in the Industrial Part of Warren I buy a lot of tools from OTC Harley Davidson or Jims Tools are 3 times the price as OTC and I can say OTC has high grade tools. 4 tool that Jims was asking 300 each I got for 100 each from OTC. I spent 400 on tools not 1200.
reply
Anthony
We do it old school. Up until a month ago we didn't even have a press. We used the old torch and freezer and BFH method. It sucked. Now we have a press, but still have to remove the entire spindle. This kit looks like a timesaver
reply
We do it old school. Up until a month ago we didn't even have a press. We used the old torch and freezer and BFH method. It sucked. Now we have a press, but still have to remove the entire spindle. This kit looks like a timesaver
reply
Vic
I suggest that you use a sharp chisel to move the bearing collar a bit just enough for the jaws of the puller to claw it. Perhaps it would be better than using a c clamp grip.
reply
I suggest that you use a sharp chisel to move the bearing collar a bit just enough for the jaws of the puller to claw it. Perhaps it would be better than using a c clamp grip.
reply
Lakario
Damn good job man. Done forget this, empty sick feeling you have when you see this on your bench when your all done. lmao, I've had that feeling before!
reply
Damn good job man. Done forget this, empty sick feeling you have when you see this on your bench when your all done. lmao, I've had that feeling before!
reply
Bryan
On my Honda I cut the bearing race on an angle as deep as I could, then took a chisel and just cracked the race. The bearing just slid off by hand
reply
On my Honda I cut the bearing race on an angle as deep as I could, then took a chisel and just cracked the race. The bearing just slid off by hand
reply
Ricardo
Thank you alot, I just purchased a 2008 Jeep compass, bushings, back wheel bearing needs replacing so watching you it cost me less by doing diy
reply
Thank you alot, I just purchased a 2008 Jeep compass, bushings, back wheel bearing needs replacing so watching you it cost me less by doing diy
reply
brk
That grinder was very close to your fingers there lol. .one slip and it's a very short vid. Love your chanel keep up the good work
reply
That grinder was very close to your fingers there lol. .one slip and it's a very short vid. Love your chanel keep up the good work
reply
Add a review, comment
Other channel videos















