
Chevy Duramax - P0540 Intake Air Heater Incorrect Voltage
video description
Date: 2020-08-05
Related videos
Comments and reviews: 10
Steve
An excellent example of logical, thoughtful diagnostic procedure. Well done sir!
Im on a personal crusade in regard to heater delete, and below have copied a rant I have posted elsewhere. One question that remains is when does the heater operate? Im guessing it is independent of glow plugs. Just watched the rest of the video and you said below 73F, but for how long?
Also, you should consider one of those over the engine, reclining creepers.
As an engineer myself, I must question mods or deletes on an engine which override the original intentions and motivations of fellow engineers who undoubtedly spent considerable time and effort designing various aspects of our Duramax engines. As we all know, economics of every aspect of vehicle design are an important part of decision making and unless a part is mandated by emissions regulations, I doubt anything is ever added without considerable research into the pros and cons. While I concede the heater coil no doubt causes some degree of intake restriction and turbulence, Im confident those downsides were on the con side of the ledger, but were overridden by the benefits of better warmup characteristics during cold weather starts. Frankly, I dont know at what ambient the heater is energized, but would be willing to bet there are benefits to warmer intake air, which may be transparent to the operator, but nonetheless contribute to better engine operating characteristics during that phase of operation.
I also suspect that, short of dyno testing, there is little noticeable performance difference following removal of the heater, and even then, improvement is only at the margins.
If anyone has numbers to refute my observations, Id luv to see them.
Delete on, homey and thanks for this otherwise well produced video.
reply
An excellent example of logical, thoughtful diagnostic procedure. Well done sir!
Im on a personal crusade in regard to heater delete, and below have copied a rant I have posted elsewhere. One question that remains is when does the heater operate? Im guessing it is independent of glow plugs. Just watched the rest of the video and you said below 73F, but for how long?
Also, you should consider one of those over the engine, reclining creepers.
As an engineer myself, I must question mods or deletes on an engine which override the original intentions and motivations of fellow engineers who undoubtedly spent considerable time and effort designing various aspects of our Duramax engines. As we all know, economics of every aspect of vehicle design are an important part of decision making and unless a part is mandated by emissions regulations, I doubt anything is ever added without considerable research into the pros and cons. While I concede the heater coil no doubt causes some degree of intake restriction and turbulence, Im confident those downsides were on the con side of the ledger, but were overridden by the benefits of better warmup characteristics during cold weather starts. Frankly, I dont know at what ambient the heater is energized, but would be willing to bet there are benefits to warmer intake air, which may be transparent to the operator, but nonetheless contribute to better engine operating characteristics during that phase of operation.
I also suspect that, short of dyno testing, there is little noticeable performance difference following removal of the heater, and even then, improvement is only at the margins.
If anyone has numbers to refute my observations, Id luv to see them.
Delete on, homey and thanks for this otherwise well produced video.
reply
Garth
Nice demo Eric, was that serpentine belt manufactured on St Patrick's Day? Nice to see how the circuits function with the control modules. Seems to me like many computer vehicles come in for problems that a non-computer vehicle would never come in for meaning, seems like the newer vintage has problems of their own which generate more maintenance vs. the old. Computer run vehicles are a dream if they work correctly however, if there's a failure while on the road, there's likely no roadside fix going to take place so it's flatbed time to a garage that is local to the breakdown location which is totally risky from my experience. Sounded like the lunch siren went off and Eric continued working as usual. Reminds me of the film, My Cousin Vinny, the local factory steam whistle at 5 AM, to tell everyone its time to get up.
reply
Nice demo Eric, was that serpentine belt manufactured on St Patrick's Day? Nice to see how the circuits function with the control modules. Seems to me like many computer vehicles come in for problems that a non-computer vehicle would never come in for meaning, seems like the newer vintage has problems of their own which generate more maintenance vs. the old. Computer run vehicles are a dream if they work correctly however, if there's a failure while on the road, there's likely no roadside fix going to take place so it's flatbed time to a garage that is local to the breakdown location which is totally risky from my experience. Sounded like the lunch siren went off and Eric continued working as usual. Reminds me of the film, My Cousin Vinny, the local factory steam whistle at 5 AM, to tell everyone its time to get up.
reply
WMichael
Great video and explanation, demonstration. As usual.
I think the big lesson is verifying the fix, using the ECM's output controls.
Having written GM Powertrain diagnostics for 25 years, that is the last step we put in.
OEM diagnostics are written for a tech/mechanic that does not have Eric's experience & skills. Therefore, they can be lengthy; however they are developed, tested, and verified on production vehicles - for all known faults that will set a DTC or cause a symptom.
reply
Great video and explanation, demonstration. As usual.
I think the big lesson is verifying the fix, using the ECM's output controls.
Having written GM Powertrain diagnostics for 25 years, that is the last step we put in.
OEM diagnostics are written for a tech/mechanic that does not have Eric's experience & skills. Therefore, they can be lengthy; however they are developed, tested, and verified on production vehicles - for all known faults that will set a DTC or cause a symptom.
reply
SATAMAN
What I'm missing here is what exactly is causing the excessive current draw inside of the plastic box. Where is the current going? Are the windings of the relay shorted? I understand the current limiters built into the PCM I just don't understand what's causing them to go into action. It can't be downstream of the box since it's replacement solved the problem so what's inside of the box to cause the current draw. Please explain.
reply
What I'm missing here is what exactly is causing the excessive current draw inside of the plastic box. Where is the current going? Are the windings of the relay shorted? I understand the current limiters built into the PCM I just don't understand what's causing them to go into action. It can't be downstream of the box since it's replacement solved the problem so what's inside of the box to cause the current draw. Please explain.
reply
iam
Hey that intake heater controller module near the fire wall on the gmc I'm trying to figure out where the ground white goes too i hooked all three wires right but I out have a black wire left which is the 4th black wire I forgot where it bolts too it's an 2003 gmc 6. 6 diesel 2500 I did the injectors
reply
Hey that intake heater controller module near the fire wall on the gmc I'm trying to figure out where the ground white goes too i hooked all three wires right but I out have a black wire left which is the 4th black wire I forgot where it bolts too it's an 2003 gmc 6. 6 diesel 2500 I did the injectors
reply
Pine
Test light master does it again! That was beautiful! Just one question: what was the amp rating for the fuse protecting the control side circuit of that shorted relay? When you grounded the relay with the jumper wire to ground and drew 12A, I'm surprised that little fuse didn't go pop lol
reply
Test light master does it again! That was beautiful! Just one question: what was the amp rating for the fuse protecting the control side circuit of that shorted relay? When you grounded the relay with the jumper wire to ground and drew 12A, I'm surprised that little fuse didn't go pop lol
reply
Tom
Great to see constant reference to the circuit diagram. Makes it very easy to understand. Another handy use for the scope-- substitute it for the relay coil. The PCM is very sensitive to overload as with the heater circuit on the O2 sensors. Informative video!
reply
Great to see constant reference to the circuit diagram. Makes it very easy to understand. Another handy use for the scope-- substitute it for the relay coil. The PCM is very sensitive to overload as with the heater circuit on the O2 sensors. Informative video!
reply
bookerol
Both of the relays were bad. 40 ohms on the glow plug coil and 1 ohm on the intake heater coil. Obviously, diesel vibration takes it's toll on those relays, eventually. Good catch Eric!
reply
Both of the relays were bad. 40 ohms on the glow plug coil and 1 ohm on the intake heater coil. Obviously, diesel vibration takes it's toll on those relays, eventually. Good catch Eric!
reply
Mike
Great Video. I've never seen a small relay do that, perhaps moisture or something got in there and did something to the insulation on the relay coil? Just thinking.
Thanks Eric.
reply
Great Video. I've never seen a small relay do that, perhaps moisture or something got in there and did something to the insulation on the relay coil? Just thinking.
Thanks Eric.
reply
Ozzstar's
That relay was kind of like a sci-fi situation. Did you get a chance to autopsy the old relay and find the contacts worn or dirty? What was causing the resistance issue?
reply
That relay was kind of like a sci-fi situation. Did you get a chance to autopsy the old relay and find the contacts worn or dirty? What was causing the resistance issue?
reply
Add a review, comment
Other channel videos















