
Did I Make The Wrong Call? Part I
video description
Date: 2020-08-05
Related videos
Comments and reviews: 10
Andrew
Had a very simular problem on my 96 BMW 7. The light came on with a front left sensor fault. It would not clear either. However like here live data was OK. So I unplugged the sensor and the connection looked slightly corroded. After cleaning and reconnecting the fault cleared and all was good. for a few weeks. Finally the moment the light came up I connected my scanner and there was no speed for that sensor. Replaced sensor (horrible job) and all good now.
reply
Had a very simular problem on my 96 BMW 7. The light came on with a front left sensor fault. It would not clear either. However like here live data was OK. So I unplugged the sensor and the connection looked slightly corroded. After cleaning and reconnecting the fault cleared and all was good. for a few weeks. Finally the moment the light came up I connected my scanner and there was no speed for that sensor. Replaced sensor (horrible job) and all good now.
reply
Not
The ABS system in that Scion uses an electrical inductive ring/sensor for the rear (built into the back of the wheel bearing but can be bought seperately) to pick up a wheel speed signal for the ABS computer.
If that magnetic sensor ring or the wheel bearing is damaged you can get intermittent issues with ABS codes.
Beyond that I suspect internal issues with the ABS module.
reply
The ABS system in that Scion uses an electrical inductive ring/sensor for the rear (built into the back of the wheel bearing but can be bought seperately) to pick up a wheel speed signal for the ABS computer.
If that magnetic sensor ring or the wheel bearing is damaged you can get intermittent issues with ABS codes.
Beyond that I suspect internal issues with the ABS module.
reply
Kyle
Sounds like a faild wheel bearing noise in the background. Sometimes it will cause WSS codes to set, scan tool live data is great. but the rate at which data is transmitted that is seen on the screen is slower than what the abs ecu sees. The graph will still have an uninterrupted line but watch the numbers. It skips substantially.
reply
Sounds like a faild wheel bearing noise in the background. Sometimes it will cause WSS codes to set, scan tool live data is great. but the rate at which data is transmitted that is seen on the screen is slower than what the abs ecu sees. The graph will still have an uninterrupted line but watch the numbers. It skips substantially.
reply
Bert
On my VW I was repaired the wire on my LF abs sensor. When I cleared the codes it reset my traction system but the ABS light would not turn off until I drived. I think it has to go through a short self-diagnostic test before it can be turned off on some foreign vehiles.
reply
On my VW I was repaired the wire on my LF abs sensor. When I cleared the codes it reset my traction system but the ABS light would not turn off until I drived. I think it has to go through a short self-diagnostic test before it can be turned off on some foreign vehiles.
reply
Wenbiao
On my Venza, the two rear ABS sensors were bad, it was the wire, at the big U bend. The broke but they are connected most of the time, only when you make a sharp turn or go through a big bump, the U bend is stretching out of shape, only then the ABS light comes on.
reply
On my Venza, the two rear ABS sensors were bad, it was the wire, at the big U bend. The broke but they are connected most of the time, only when you make a sharp turn or go through a big bump, the U bend is stretching out of shape, only then the ABS light comes on.
reply
Ranger
Had that once before - code cleared itself shortly afterwards. Not sure why it wouldn't clear out with the tool. Maybe it did but for some reason the computer just didn't register / recognize it till after a number of clean restarts.
reply
Had that once before - code cleared itself shortly afterwards. Not sure why it wouldn't clear out with the tool. Maybe it did but for some reason the computer just didn't register / recognize it till after a number of clean restarts.
reply
billy
Load test the wiring from the speed sensor too the module. Have found a lot of issues when load testing. Look on amazon for es load pro test leads. Best 50 buck you will ever spend. Takes a lot of guess work out of the job.
reply
Load test the wiring from the speed sensor too the module. Have found a lot of issues when load testing. Look on amazon for es load pro test leads. Best 50 buck you will ever spend. Takes a lot of guess work out of the job.
reply
bob
So either the ECU
the Speed Sensor
the signal sent
the signal received
the tool (reader)
the soft ware coding in the ECU DOESN'T MATCH AND MAKE THE TOOLS HAPPY ENOUGH TO CLEAR THE CODE.
reply
So either the ECU
the Speed Sensor
the signal sent
the signal received
the tool (reader)
the soft ware coding in the ECU DOESN'T MATCH AND MAKE THE TOOLS HAPPY ENOUGH TO CLEAR THE CODE.
reply
Dan
corrosion on the connector end likes to cause this. new ABS wire might save it if the pins on the bearing arnt toast already (sounds like they arnt) do alot of these at the dealer.
reply
corrosion on the connector end likes to cause this. new ABS wire might save it if the pins on the bearing arnt toast already (sounds like they arnt) do alot of these at the dealer.
reply
Deftones
At least you don't have to deal with analog meter sweeps for codes much anymore. I used to hate that crap when i was a tech. Abs modules are pain in the ass
reply
At least you don't have to deal with analog meter sweeps for codes much anymore. I used to hate that crap when i was a tech. Abs modules are pain in the ass
reply
Add a review, comment
Other channel videos















