• Vehicles • Fashion • Recipes • Blogs • Hunt • Travels • Sport • Fun • Handmade • IT • Education
Mini-Games
x

x
zakruti.com » Auto & Vehicles » South Main Auto Repair
Chevrolet Silverado 5. 3: Misfire

Chevrolet Silverado 5. 3: Misfire

FBTwitterReddit

video description

Rating: 4.0; Vote: 1
In an effort to salvage a video I came out with this one. I have been messing with a screen recorder on my Autel 908 and it really messed up on the first vid to the point it just wasn't usable. Needless to say I drag you along for Part 2 and try to salvage what I can. Oh well, some days you get the bear and some day the bear gets you
Date: 2020-08-05

Comments and reviews: 10


I'd have been curious to see the injector resistance or a current ramp of the failed injector compared to the others. Typically when an injector coil resistance decreases due to an internal short, it will begin to overfuel because the increased current opens the injector faster (reduces its latency. Remember the old GM Multec injectors? When they shorted (assuming they didn't smoke the ECM injector driver) they would make the engine run horribly rich because the injector opened much faster. Typically it is more noticeable at idle and lower load because the actual amount of time the injector is spraying fuel is extremely short at idle, typically around a millisecond, even though the commanded injector PW might be 2. 5-3ms. Thats because 1 or 2ms of that may be the amount of time it takes for the injector to physically open, so if the injector pw is 3ms, 1. 5ms of that may be the time needed to open the injector and the other 1. 5ms is the actual time the injector is spraying fuel. If the injector is internally shorted and opening faster, say in 0. 5ms, you now have 0. 5ms of injector opening time (latency) and 2. 5ms of the injector spraying fuel, thus the cylinder runs rich.
reply

I have a 1999 1/2 Chevrolet silverado with 5. 3 LS and E4160trans. is 4 wheel drive, 4wheel disc brakes, 128K miles Problem I'm having is the TCC (torque converter clutch) engages when you depress the accelerator going uphill above 50mph and when cruising with light accelerator pedal pressure it disengages and rpm. s go up 200. Not showing any trans codes. Truck has catback aftermarket exhaust and cold air intake which was on the truck when I bought it. The catback exhaust was added recently, truck is driven gently not run hard. TPS was recently replaced but didn't fix problem, but truck was more responsive to throttle input. Transmission fluid looks clean has about 10k miles since filter fluid change. Any ideas where problem might be?
reply

I was looking at mode6 data on my 2011 5. 3 Silverado (107k miles) and was surprised to see up to 4 misfires counted on random cylinders ( both banks) when I revved the engine to 2000 rpm. No misfire at idle. Count would go back to zero, then maybe 2 then back to zero. Never a code set and you would never know it unless you looked at the data. Other parameters like fuel trims, O2, etc all in normal operating range. No idea if this is normal or not - anyone ever see this?
reply

i thought the clips on the injectors prevented any kind of movement and locked them into the fuel rails. that is probrally why the o-rings were ripped on the other ones. the clips should have been replaced (re-purchaced) and put back on the injectors that were missing those clips. same thing might happen again to the other injectors eventually
reply

You mentioned how the pcm was compensating for the excessive fuel from the failed injector 6 on that bank earlier in the video. After the repair i noticed all injectors on bank 2 looked like they were flowing slightly more fuel. Would itbbe a good idea to reset KAM or even just the adaptives before rerunning the injector drop test?
reply

Eric, I don't think you can use silicone/dielectric grease or silicone (dry lubricant) spray on fuel injectors because the silicone chemically damages the oxygen sensors and catalyst materials FYI. Service manuals usually say use clean engine oil only for this reason.
reply

Oh baby, we gotta add a comment, they are at 666, need to make it 667. LOL, yeah, my fat sausages dont work exactly like they used to either. It is what it is. You just learn to adapt.
reply

You do a great job, I learn so much from your video's, the sound, lighting, camera angles are all excellent, I feel like I'm there watching over your shoulder.
reply

So what do you think caused the #6 injector to close later(lower pressure) then the other injectors? Gummy injector? Weak return spring, worn pintle valve?
reply

Very informative and helpful! Thank you very much for all the effort you put in to these videos. Were so fortunate to have you on YouTube. Ive learned a ton!
reply
Add a review, comment






Other channel videos